![]() Fortunately, Wi-Fi gateways and multiplexers are becoming widespread on our boats, allowing us to connect to any type of computer and mobile device, to work with our favorite navigation apps. Summary, temporaly, there are still fixes to be expected with future updates of the operating system of Macs both in USB connection and Bluetooth. There, at least, everything works just fine ! Regardless of the connected Wi-Fi gateway sending NMEA data, with MacENC as with Weather4D Routing & Navigation :Įven with OpenCPN, but beware, a lot of malfunctions could occur with this version not adapted to macOS 11 and later. GNS3000 with a speed = 38400. But, once again, incomprehensibly, it may happen that the connection does not establish. With OpenCPN 5.6.0 we must use the same trick as that described by Eric Rodriguez when creating the serial port = /dev/cu. CoolTerm Software (download for free from link below) Procedure: Download the free CoolTerm software Download CoolTerm. With Weather4D enabled in the Mac's "Location Service" settings, the GPS position is well received from the GNS3000 : Baud rate: choose custom and input 1500000.Click the Option menu and set the following. ![]() On my first try I had no problems, except that the data was only received at the speed of 38400 bps (while the device is factory set to transmit at 4800 bps) :Īs for the USB connection, MacENC圆4 recognizes the GNS3000 port by selecting the type = Other and flow rate set to 38400. When it works, it is super ! The GNS3000 is well recognized and the connection can be activated. Note that the latest version of OpenCPN 5.6.0 for Mac is not given as compatible with macOS 11/12 and does not detect the serial port. Weather4D Routing & Navigation does not read the serial port, because this function does not exist on iOS. I specify that I tested with my "old" BU-353S3 who is more than ten years old, not the most recent BU-353S4 or BU-353N.īut beware, to date only the navigation application MacENC圆4 directly recognizes the serial port, by selecting the type = SIRF USB, and displays the position. Avec l’utilitaire CoolTerm, we can now display the NMEA sentences that are sent by the GPS. ![]() Once the BU-353 is connected to a USB port on the Mac M1 (using a USB-C converter), le nouveau driver crée un port série usbserial-xxxx, qui s’appelle aussi PL2303-USBtoUARTxxxx. As for the GNS3000 ( ¹) in Bluetooth it always undergoes an instability of the interface for the connection of multiple devices, instability that unfortunately does not yet seem to be fully fixed. In USB, Latest Driver Prolific V.2.2.2 is now universal for GPS BU-353xx by GlobalSat. I2cuart.The arrival of Macs with Apple M1 processors and macOS systems 11 "Big Sur" and macOS 12 "Monterey" had caused disappointments among GPS users connected via USB and/or Bluetooth for their navigation applications. I2cuart.digitalWrite(1, LOW) //start calibration of MH-Z16 under 400ppmĭelay(10000) //5+ seconds needed for the calibration process I2cuart.pinMode(1, OUTPUT) //set up for the calibration pin. Make sure that the sensor has been running in fresh air (~400ppm) for at least 20 minutes before calling this function. Zero Point (400ppm) Calibration function for NDIR sensor. I2cuart.digitalWrite(0, 0) //turn off the power of MH-Z16 I2cuart.pinMode(0, INPUT) //turn on the power of MH-Z16 I2cuart.pinMode(0, INPUT) //set up for the power control pin Coolterm Download Mac Voigtlander 28mm 1.9 Serial Number For Mac Adobe Cs5 Adobe Dynamic Link Download Mac Macfamilytree Serial 6.3. Step 2 - Configure and select the Serial Port Configure the serial port and select the serial port. First you need to select and configure the serial port by pressing the options button. ![]() Step 1 - Start CoolTerm CoolTerm is idle state when you open it. ![]() Power control function for NDIR sensor. You can download CoolTerm here ( mirror ). Serial.println("Sensor communication error.") Wait for the NDIR sensor to initialize. Serial.println("Wait 10 seconds for sensor initialization.") I am using an Arduino UNO, and using an Infrared CO2 sensor. The data shows up, but there is no timestamp, and I want to transfer the data to Excel. I am having a spot of trouble using PuTTY to transfer the information printed on my serial monitor. ![]()
0 Comments
Leave a Reply. |